Beaucatcher Fly Fishing
Premier Fly Fishing Services
Menu:
Emerald Heron Spey
Syd Glasso style pattern
tied by Bruce E. Harang
Materials:
Hook:
Return loop up eye salmon, size and weight to suit (here Partridge code
CS10/1G)
Thread: Gudebröd 6/0, White or other light color as working
thread
Hackle:
Whiting black spey hackle or similar
First Rib: Medium
flat sliver tinsel
Second Rib: Small oval silver tinsel - overlaid on first rib
Body: Rear 2/3 - BT emerald floss; front 1/3 - green seal
or substitute
Throat:
Coque dyed green
Wing: Black hackle tips
Head:
Gudebröd 6/0, Light Olive
Tying Instructions:
1. Mount an up eye return loop salmon hook in your vise.
2. Attach the thread at the point the wings will be tied in and wrap a smooth flat thread base to a point just above the point of the hook. If you are using an in-line rotary vise an easy method is to use one finger of your working hand as a moving thread bobbin holder and use the off hand to turn the vise while moving the thread rearward. If you start with an untwisted thread and let the bobbin hang free you will create a very thin flat thread base. I prefer to use a very light working thread such that if the materials over it become translucent in the water their colors are not muddied by a dark background.
3. Tie in the spey hackle by the tip, then the ribs, tying in the flat tinsel closer to you than the oval tinsel. I tie the spey hackle and rib on the bottom of the hook. This allows puts the exposed hackle stem section in front of the hook bend to protect it. Leave tag ends on these materials that reach at least to a point 1/3 of the hook shank length behind the eye to provide a smooth even underbody for the floss.
4. Bring the thread back to the 1/3 point of the hook shank binding down the ribs and spey hackle. Again an easy way of creating this smooth thin flat underbody of thread with an in-line rotary vise is to use your working hand as a moving thread bobbin but this time moving forward. Tie in a length of BT emerald silk floss (here Pipers 90 denier silk floss), or substitute synthetic floss, by wrapping forward from the tie in point using 5 very tight turns of thread. Leave a silk tag that reaches to the starting point of the fly or longer.
5. Wrap the floss back to the rear of the body and then forward to its tie in point. Of course you want to avoid tying down any of the spey hackle fibers. Unwrap 4 of the tight binding wraps used to mount the silk and then tie down both ends of the silk with a few tight wraps of thread. To create the smoothest floss body burnish the floss to smooth out and pack the silk fibers. Create a dubbing loop against the front end of the floss and then bring the thread forward to the starting point. The smoothness of the underbody is not as critical here as the front body portion is dubbed.
6. Insert a small amount of seal dubbing or substitute (here the dubbing is SLF green), spin the dubbing loop to lock the dubbing in place, pluck out any loose dubbing fibers, wrap the dubbing in touching turns to the front of the body, and tie off. Cut off any excess dubbing and loop.
7. Wrap the flat rib forward in 5 turns and tie off. Next wrap the oval rib over the center of the flat tinsel so it is overlaid onto the flat rib.
8. Bring the spey hackle forward wrapping it immediately behind the rib and tie off in the front. Cut the excess. Tie off the working thread and cut it off. Mount the red thread used to make the head. Tie in a collar of 1-- 2 wraps of coque dyed green. Cut off any excess feather.
9. The wing comprises two pair of black hackle tips. The pairs are mounted curved toward one another to form a knife blade wing having a length longer than the body but short of the bend of the hook so that the wing can not fowl around the hook shank. The wings should be mounted low over the body (here the wings are as high as you would want and a bit lower would be better). To mount the wing take all four feathers and size them leaving the bare stems connected. Insert the four bare stems through the hook eye and position the wing base just in front of the teal collar. Tie down with several very tight thread wraps and check the wing to insure desired position. When you are satisfied with the wing position, pull the stems out of the hook eye and cut off flush with the binding wraps.
10. Complete a small proportional head and apply head cement and gloss finish. I use Griffs Thin penetrating head cement to lock everything together and then Sally Hansen Hard as Nails with Nylon finger nail polish for the gloss finish. This product does not absorb water and therefore does not turn milky white when being fished. If I have bleeding through of the black hackle wing stems I coat the head with several light coats of a red finger nail polish.
© 2008 Bruce E Harang